This page consolidates the version history for each previous Hub 360 release.
On this page:
Hub 360 1.6
Workflows Screen
A new screen has been added to give you an overview of all routes and bookings created in Hub 360. | |
Start and Stop Makito Encoder Streams
On the Appliances screen, for Makito Encoders added display and control of streams and encoders. | |
Mobile Transmitter Geolocation
Added display of GPS coordinates on the Appliances screen for paired Air and Pro transmitters and MoJoPro connections. Administrators can enable/disable this setting across all appliances, or you may enable/disable the individual appliance's location in the settings on the Appliances screen. | |
Hub 360 1.5
Initial SRT Gateway Support
SRT Gateway devices can now be paired to Hub 360. However, only limited functions are available. Full support for SRT Gateway will be available in a future release. | - Supported Appliances and Versions
- Appliance Network Requirements for Use in Hub 360
- Adding an Appliance
- Editing Appliance Settings
- Viewing and Editing Appliance Details
|
External Sources and Destinations
If your device is not yet supported in Hub 360, you may add an external source or destination and populate pre-existing SRT streams within these devices. You can then use these streams in the Master Control screen to create routes. See the following note for limitations.
Note
- Currently, only SRT streams in listener mode are supported.
- In the Master Control screen, external source streams can only be routed to Makito decoders and Cloud StreamHubs.
- In the Master Control screen, only Makito encoder sources can be routed to external destination streams.
- External sources and destinations do not count against your license's appliance usage.
| - Adding an Appliance
- Viewing and Editing Appliance Details
- Viewing Appliance Details
- Adding and Editing Streams on External Appliances
- Viewing Source Status
- Viewing Destination Status
|
Booking by StreamHub Priority
| Added ability to prioritize StreamHubs within groups for auto-generated routes from transmitters or MoJoPro devices. | - Managing the Priority of StreamHubs within a Group
- Understanding StreamHub Usage with Automated Routes
|
Makito FX Encoder Support in Master Control
| With the release of Makito FX Encoder 1.1, these encoders are now fully integrated with Hub 360. You can create and edit streams using them in the Master Control screen, and you may initiate an SSH tunnel to interact directly with the encoder's interface. | - Supported Appliances and Versions
|
Remote Connection to StreamHub using Domain Name
| In the StreamHub appliance settings, added an Interface Address textbox, allowing you to specify a custom address or domain name for appliance interface access. This address or domain is used when accessing the appliance interface via Hub 360. | - Editing Appliance Settings
|
Streaming Address for Makito Decoders
| You can now configure a streaming IP address or domain for your paired Makito Decoders. If configured, this address will be used to connect to the decoder for video transmissions. | - Editing Appliance Settings
|
Improved Performance of Renaming Makito Devices
| Whether you rename your Makito devices in the Hub 360 interface or in the individual Makito web interfaces, both will now stay in sync. | N/A |
Hub 360 1.4
MoJoPro Licenses on Hub 360
A MoJoPro license allows you to stream from the app to any paired StreamHub. With StreamHub 4.5+, you can use MoJoPro licenses already present on paired StreamHubs. Contact your Sales representative to purchase these licenses. | - Admin Area Screen
- Reviewing MoJoPro Licenses
|
Streaming Address for StreamHub
| You can now manually configure a streaming IP address or domain for your paired StreamHubs. If configured, this address will be used to connect to the StreamHub for video transmissions. | - Viewing and Editing Appliance Details
- Viewing Appliance Details
- Editing Appliance Settings
|
Hub 360 1.3.3
Enhanced Activity Feed
| Added new message types to the Admin Area's Activity Feed. | |
| Non-administrator accounts now have access to the Admin Area's Activity Feed screen to view limited messages. | |
| Added search option for the Activity Feed. You may search for device name, group name, or pairing code name. | - Admin Area Screen
- Viewing Activity Feed
|
Route Configuration Modal
| In the Master Control screen, if a StreamHub route has yet to be configured, after selecting a route's source, a new configuration modal appears to configure the route's outputs. | |
StreamHub Route Tiles
| In the Master Control screen, the StreamHub route tiles now indicate the output number and protocol used. | |
Route/Booking for offline transmitters
| You can now create/edit routes in MCR when your transmitters (Air, Pro, and Rack) are offline. | |
Appliance Name Auto-Refresh
| Support for automatic refresh of appliance names when their names are changed in the individual appliance's UI. | |
Hub 360 1.3.2
Hotfix release only.
Hub 360 1.3.1
Hotfix release only.
Hub 360 1.3
Full Support for Makito X4 Decoder
The Master Control section now fully supports the Makito X4 Decoder as a receiver. You can easily create SRT routes to this appliance and monitor the associated telemetry. | - Supported Appliances and Versions
- Viewing Destination Status
- Routes Pane
- Create a Makito Encoder to Decoder SRT Connection
|
Searching on Master Control
| Added search functionality in the Master Control screen. | |
Activity Feed
Added Activity Feed tab in the Admin section, so that you can now display the history of completed actions or events. In the future, this feature will log more event types. | - Admin Area Screen
- Viewing Activity Feed
- Activity Feed Entries
|
What's New Dialog
| Added a What's New dialog that provides a summary of the main improvements and features as each new version is released. | |
Network Requirements Documentation
| Added documentation for network requirements before connecting your appliances to Hub 360. | - Appliance Network Requirements for Use in Hub 360
|
Hub 360 1.2
Firmware Upgrades
| Added ability to upgrade the firmware of your Makito or transmitter (Air, Pro, Rack) appliances. | |
Filtering by Group
Added ability to filter the items in the Master Control and Appliances screens by Group. | - Master Control Screen
- Sources Pane
- Routes Pane
- Appliances Screen
|
Searching Appliances
| Added ability to search the Appliances list by various appliance information, not just the appliance name. | |
Full Support for Makito X1 Encoder
| Added Master Control support for the Makito X1 Encoder. | - Supported Appliances and Versions
|
Hub 360 1.1
Initial public release
